SERVICE PROCEDURES
2027 40mm FLOAT NA3 Glidecore Rebuild
Required Parts
- 803-04-703 Seal Kit: 2027 40 FLOAT NA 3 Glidecore Rebuild, Two Piece Neg Plate
Required Tools
- 398-00-657 Tooling: Bullet, Sealhead To Shaft, FLOAT NA 2
- 398-00-681 2002-017 32 Damper-side and ALL 32-34-36-40 Spring-side Removal Tool
- 398-00-682 2005-017 34-36-40 Damper-side Removal Tool
- 398-00-706 Tooling: Fork Topcap Socket, 32mm V2, 3/8 Drive
- 398-01-298 Tooling: Custom Hex Socket, 22mm, 2026 36 & 36 E-Opt, Neg Plate
- 803-01-324 Kit: Tooling: 2019 Clamps, Grip Damper, Body and Shaft
WARNING: Always wear safety glasses and protective gloves during service to prevent potential injury. Failure to wear protective equipment during service may lead to SERIOUS INJURY OR DEATH.
The following procedure guides you through the rebuild of the FLOAT NA3 Glide core air spring found in 2027 40mm forks.
WARNING: FOX products should be serviced by a trained bicycle service technician, in accordance with FOX specifications. If you have any doubt whether or not you can properly service your FOX product, then DO NOT attempt it. Improperly serviced products can fail, causing the rider to lose control resulting in SERIOUS INJURY OR DEATH.
WARNING: Never attempt to modify air volume spacers or air shaft assemblies, as this can damage your fork causing a loss of control of the bicycle leading to SERIOUS INJURY or DEATH.
WARNING: FOX suspension products contain pressurized nitrogen, air, oil, or all 3. Suspension misuse can cause property damage, SERIOUS INJURY OR DEATH. DO NOT puncture, incinerate or crush any portion of a FOX suspension product. DO NOT attempt to disassemble any portion of a FOX suspension product, unless expressly instructed to do so by the applicable FOX technical documentation, and then ONLY while strictly adhering to all FOX instructions and warnings in that instance.
WARNING: Modification, improper service, or use of aftermarket replacement parts with FOX forks and shocks may cause the product to malfunction, resulting in SERIOUS INJURY OR DEATH. DO NOT modify any part of a fork or shock, including the fork brace (lower leg cross brace), crown, steerer, upper and lower leg tubes, or internal parts, except as instructed herein. Any unauthorized modification may void the warranty, and may cause failure or the fork or shock, resulting in SERIOUS INJURY OR DEATH.
WARNING: Please verify that all air has been released from the air chamber by pushing down on the Schrader valve core. Failure to release all air pressure before further disassembly may cause parts to eject causing SEVERE INJURY OR DEATH.
Step 1
Wipe the grease off the air shaft assembly to make it easier to handle. Clamp the piston body securely in a soft-jaw vise.
Step 2
Unthread the air piston counterclockwise using a 10 mm socket. Lift the dome-shaped piston off the piston base to remove it. Remove the piston band , and set it aside
Step 3
Remove the Q-ring from the piston and replace it with a new greased one from the kit. Reinstall the gray piston band.
Step 4
Clean the shaft with isopropyl alcohol, then clamp it securely in the 10 mm Shaft Clamps (PN: 803-01-324). Using a 4 mm Allen wrench, unthread the piston bolt counterclockwise.
Step 6
Remove the piston bolt and replace the compliance O-rings with new, greased O-rings from the kit. Reinstall the piston bolt onto the piston cap. Apply 1–2 drops of red Loctite 263 to the threads, then thread the piston cap onto the piston body and torque to 80 in-lb(9Nm).
Step 7
Reinstall the top-out spacer, followed by the piston bolt O-ring. Apply 1–2 drops of red Loctite 263 to the air shaft threads, then install the piston bolt and torque to 50 in-lb(5.6Nm).
Step 8
Clamp the piston body securely in a soft-jaw vise. Reinstall the domed piston onto the piston body. Using a 10 mm socket, torque the domed piston to 120 in-lb (13.6 Nm).
Step 9
Clean the shaft with Isopropyl alcohol then clamp it in your 10mm shaft clamps (PN: 803-01-324). Remove and discard the o-ring from the base stud.
Step 10
Carefully apply heat to the shaft at the base stud with a propane torch for 5-10 seconds to break down the Loctite. Unthread the base stud counter-clockwise with a 12mm wrench, then lift up to remove. Remove MCU bumper and Neg plate.
Step 11
Insert a 4 mm hex wrench through the holes in the negative plate tube and hold it securely. Using the Negative Plate Socket (PN: 398-01-298), hold the socket firmly against the negative plate and unthread it counterclockwise from the negative plate tube.
Step 12
Remove the seal carrier from the negative plate housing. Remove the compliance O-ring, Q-ring, and housing O-ring, then replace them with new, greased ones from the kit.
Step 13
Reinstall the seal carrier. Apply 1–2 drops of blue Loctite 243 to the capture plate threads, then install and torque the capture plate to 50 in-lb using the Negative Plate Socket (PN: 398-01-298).
Step 14
Reinstall the top-out bumper. Insert the Bullet Tool (PN: 398-00-657) into the shaft, then apply a thin film of Slick Honey. Reinstall the negative plate with the flat side facing down, then the MCU bumper. Remove the bullet tool.




























![img/help/page3217-RDLC/IMG_2028 [Recovered] copy.jpg](img/help/page3217-RDLC/IMG_2028 [Recovered] copy-t.jpg)








































